Open new windowSee all data sheetsRecommend selecting the PDF printerPDF-IMAGE


FINANCIERA MADERERA S.A. (FINSA)
N-550, KM 57
15890 SANTIAGO DE COMPOSTELA (A CORUÑA)
SPAIN
DECLARATION OF PERFORMANCE Nº 00128
11/19/2018
SUPERPAN H TECH P5
Manufactured at: Luso Finsa
Estrada Nacional 234, Km 92.7
3524-952 NELAS (PORTUGAL)
PRODUCT TYPEINTENDED USEAVCP*NOTIFIED BODY AND REFERENCECERTIFICATE NUMBER
P5Internal use as structural components in humid conditions2+AENOR 00990099/CPR/A65/0036
*Assessment and verification of constancy of performance system according to Annex V of regulation (EU) No 305/2011

PROPERTIESTEST METHOD UNITS THICKNESSES mm
>10/13>13/20>20/25>25/32>32/40
CHARACTERISTIC STRENGTH
TABLE 5 EN 12369-1:2001
BENDING FMEN 13986:2004+A1:2015N/mm215,013,311,710,08,3
COMPRESSION FCEN 13986:2004+A1:2015N/mm212,711,810,39,88,5
TENSION FTEN 13986:2004+A1:2015N/mm29,48,57,46,65,6
PANEL SHEAR FVEN 13986:2004+A1:2015N/mm27,06,55,95,24,8
PLANAR SHEAR FREN 13986:2004+A1:2015N/mm21,91,71,51,31,2
CHARACTERISTIC STIFFNESS (MOE)
TABLE 5 EN 12369-1:2001
CHARACTERISTIC DENSITYEN 13986:2004+A1:2015N/mm2650600550550500
TENSION ETEN 13986:2004+A1:2015N/mm220001900180015001400
COMPRESSION ECEN 13986:2004+A1:2015N/mm220001900180015001400
BENDING EMEN 13986:2004+A1:2015N/mm235003300300026002400
PANEL SHEAR FVEN 13986:2004+A1:2015N/mm2960930860750690
FINANCIERA MADERERA S.A. (FINSA)
N-550, KM 57
15890 SANTIAGO DE COMPOSTELA (A CORUÑA)
SPAIN
DECLARATION OF PERFORMANCE Nº 0012811/19/2018
SUPERPAN H TECH P5

SUPERPAN H TECH P5
TECHNICAL DATA-AVERAGE VALUES
Rev: 03/28/2018
PROPERTIESTEST METHOD UNITS THICKNESSES mm
>10/13>13/20>20/25>25/32>32/40
DENSITY (*)EN 323kg/m3750720710700675
INTERNAL BONDEN 319N/mm20,600,600,550,500,45
BENDING STRENGTH EN 310N/mm22828262019
MODULUS OF ELASTICITY EN 310 N/mm235003500320030002800
THICKNESS SWELLING 24 H EN 317%101010109
DIMENSIONAL MOVEMENT LENGTH/WIDTH EN 318%0,40,40,40,40,4
DIMENSIONAL MOVEMENT TICKNESS EN 318%66666
SURFACE SOUNDNESS EN 311N/mm2>1,1>1,1>1,1>1,1>1,1
MOISTURE CONTENT EN 322%8+/-38+/-38+/-38+/-38+/-3
FORMALDEHYDE CONTENT EN ISO 12460-5mg/100 g≤ 8≤ 8≤ 8≤ 8≤ 8
SCREW HOLDING. EDGEEN-320N800800800800800
SCREW HOLDING. SURFACEEN-320N11001100110011001100
REACTION TO FIRETABLA 8 EN 13986:2004+A1:2015 IEN 13501-1ClassD-s2,d0**D-s2,d0***D-s2,d0D-s2,d0D-s2,d0
REACTION TO FIRETABLA 8 EN 13986:2004+A1:2015 IEN 13501-1ClassDfl-s1Dfl-s1Dfl-s1Dfl-s1Dfl-s1
SWELLING IN THICKNESS AFTER CYCLIC TEST (V313)EN 321 / EN 317%121211109
INTERNAL BOND AFTER CYCLIC TEST (V313)EN 321 / EN 319N/mm20,250,220,200,170,15
SOUND ABSORPTION COEFFICIENT (Α) (250 A 500 HZ)EN 13984:2004+A1:2015α 0,100,100,100,100,10
SOUND ABSORPTION COEFFICIENT (Α) (1000 A 2000 HZ)EN 13984:2004+A1:2015α 0,250,250,250,250,25
THERMAL CONDUCTIVITYEN 13984:2004+A1:2015W/ (m·K)0,150,140,140,140,14
AIRBORNE SOUND INSULATION (SURFACE MASS) (R)EN 13986:2004+A1:2015db2628303132
WATER VAPOUR PERMEABILITY DRY CUPEN 13986:2004+A1:2015μ 6666666666
WATER VAPOUR PERMEABILITY WET CUPEN 13986:2004+A1:2015μ 5050505050
BIOLOGICAL DURABILITY USEEN 13986:2004+A1:2015Class of use1 & 2 1 & 2 1 & 2 1 & 2 1 & 2
CONTENT OF PENTACHLOROPHENOL (PCP)EN 13986:2004+A1:2015%<5<5<5<5<5
MECHANICAL DURABILITYEN 13986:2004+A1:2015Kmod KdefTabla 3.1, EN 1995-1:2004;Tabla 3.2, EN 1995-1:2004; Tabla 3.1, EN 1995-1:2004;Tabla 3.2, EN 1995-1:2004; Tabla 3.1, EN 1995-1:2004;Tabla 3.2, EN 1995-1:2004; Tabla 3.1, EN 1995-1:2004;Tabla 3.2, EN 1995-1:2004; Tabla 3.1, EN 1995-1:2004;Tabla 3.2, EN 1995-1:2004;
(*) VALUES TO BE CONSIDERED AS A ROUGH GUIDE ONLY.

(**) Mounted without an air gap behind the SuperPan H Tech P5. Mounted with a closed air gap not bigger than 22 mm behind the SuperPan H Tech P5 classificationD-s2,d2. Classification E for any other more restrictive condition. Commission Decision 2007/348/EC

(***) Mounted without an air gap behind the SuperPan H Tech P5, or with a closed air gap behind the SuperPan H Tech P5 for thicknesses equal or greater than 15mm or with an open air gap behind the wuperPan Tech P5 for thicknesses equal or greater than 18 mm . Mounted with a closed air gap not bigger than 22mm behind the SuperPan H Tech P5 classification D-s2,d2 in thicknesses between 10 and 18 mm. Commission Decision 2007/348/EC.

These physical-mechanical values improve/comply with the P5 classification established in EN 312:2010 European Standard, Tables 7 and 8. Structural boards used in moist environments (Type P5). Requirements for the specified mechanical and swelling properties. Requirements for use in humid contitions.

SuperPan H Tech P5 meets Class E1 requirements (analysed according EN ISO 12460-5) as defined in EN 312:2010 European Standard.

SuperPan H Tech P5 holds CE Certificate of conformity of the factory production control issed by the European Notified Body AENOR.

The performance of the reference product are in compliance with the performance declared above
This Declaration of Perfomance is issued under the sole responsibility of FINANCIERA MADERERA S.A. (FINSA)
Javier Portela
FINSA R&D + Quality Director
Santiago de Compostela 11/19/2018

Non dangerous product. Adequate ergonomic techniques and IPEs must be used when handling. Dust generated in cutting, sanding, drawmilling and other processes must be extracted from the working environment with the usual procedures in the wood industry as industrial vacuum systems and IPEs use must be observed according to law.