 |
| PUREFLOOR 7AC4 |
| CLASSIFICATION ACCORDING TO EN 685 Rev: 11/14/2016 |
| CARACTERISTIQUES | | REQUIREMENT | TEST METHOD |
| USE LEVEL |  | DOMESTIC INTENSE, COMERCIAL MODERATE | EN 685:95 ANNEX A |
| CLASS | | 23-31 | EXAMPLES: RESIDENTIAL, BEDROOM, CLASSROOMS, HALLWAYS, HOME OFFICES. |
| GENERAL SPECIFICATIONS |
| CARACTERISTIQUES | | REQUIREMENT | TEST METHOD |
Thickness of element (t );
t =7 mm |
| ∆ t av, (relative to nominal value)0,50
t max -t min0,50 | EN 13329 ANNEX A |
| Length of the surface layer (l) l=1200 mm | | ∆ l0,5 | EN 13329 ANNEX A; EN 13329 ANNEX A |
Width of the decorative surface (w )
w =189 mm | | ∆ w av, (relative to nominal value)0,10w max - w min0,20 | EN 13329 ANNEX A |
| Squareness of the element (q) | | Qmax =<0,20 mm | EN 13329 ANNEX A |
| Straightness of the surface layer (s) | | smax =<0,36 mm | EN 13329 ANNEX A |
| Longitudinal flatness (f) | | fconcavo=<6 mm
fconvexo=<12 mm | EN 13329 ANEXO A |
| Transversal flatness (f) | | fconcavo =<0,28 mm
fconvexo =<0,38 mm | EN 13329 ANEXO A |
| Opening between elements (o) | | oaverage =<0,15
omax =<0,20 | EN 13329 ANNEX B |
| Height between elements (h) | | hmedio =< 0,07
hmax =<0,10 | EN 13329 ANNEX B |
| Dimensional variations after changes in
relative humidity (l,w) |
| ∆l av =<0,9
dwmedio =<0,9 | EN 13329 ANNEX C |
| Light fastness |
| Blue wool scale, part B02, not worse than 6
Grey scale, part A02, higher or equal to 4 | EN-ISO 105 / EN 20105 |
| Static indentation |
| No visible changes i.e. =<0,01 mm indentation
using a straight steel cylinder with 11,30 mm in
diameter | EN 433 |
| Surface soundness | | >= 1,00 N/mm2 | EN 13329 ANNEX D |
| CLASSIFICATION REQUIREMENTS AND LEVEL OF USE |
| CARACTERISTIQUES | | REQUIREMENT | TEST METHOD |
| Abrasion resistance |
| AC 4 | EN 13329 ANNEX E |
| Impact resistance |
| IC 1 | EN 13329 ANNEX F |
| Staining resistance |
| 5 (gr 1 - 2) 4 (gr. 3) | EN 438 |
| Effect of a furniture leg |
| No damage shall be visible when tested with foot | EN 424 |
| Effect of a castor chair |
| No changes in appearance or damage, as
defined in EN425. Single-wheel castor, as
defined in EN 12529:1998, 5.4.4.2. (Type W). | EN 425 |
| Thickness swelling |
| =< 18,0% | EN 13329 ANNEX G |
| ADITIONAL PROPERTIES |
| CARACTERISTIQUES | | REQUIREMENT | TEST METHOD |
| Humidity at dispatch from manufactured | | The element shall have a moisture content of
4% to 10%. Any single batch must be
homogeneous with Hmax-Hmin = <3 % | EN 322 |
| Appearance, surface deffects | | Minor surface defect as defined in EN438 are
permitted | EN 438 |
| Edges sealing | | Complete edge sealed with oil-wax product for
enhance water resistant | INTERNAL |
| Mechanical locking strenght |
| fmax long. >=3,5 KN/m fmax transv. >=3 KN/m f0,2 long. >=3 KN/m f0,2 transv. >=2,5 KN/m | ISO 24334:2006 |
| Formaldehyde emissions HCHO | | E1≤0.124mg/m3 (EN 717-1) | EN 14041 / EN 717-1 / EN 717-2 |
| Reaction to fire | | Cfl s1 | EN 14041 / EN 13501-1 / EN ISO 9239-1 / EN ISO 11925-2 |
| Slip resistance coefficient under dry conditions |
| Class DS (>=0,3) | EN 14041 / EN 13893 |
| Slip resistance | | 35>Rd>15 | EN 12633:2003 |
| | Class 1 | CTE DB SUA 1 |
| Thermal Resistance | | Without Underlay: 0,06 m2·K/W
+ FINfloor PE Underlay 0,154 m 2·K/W
+ Finfloor Silent Underlay 0,127 m 2 ·K/W Suitable
for warm-water underfloor heating systems | EN 14041 / EN 12664 |
| Antibacterial efficiency | | Reduction of bacterial activity in 24 hours ≥ 99.9% according to tests carried out at the IMSL | ISO 22196 |
| CE Certificate | | DoP 08008 | EN 14041 |
| The above information is subject to modifications for the benefit of further improvements. |