Open new windowSee all data sheetsRecommend selecting the PDF printerRecommend selecting the PDF printer

FINFLOOR NEW ESSENTIAL UNDERLAY
CLASSIFICATION ACCORDING TO  EN 685
Rev: 10/07/2009
CARACTERISTIQUESREQUIREMENT TEST METHOD
USE LEVEL0EN 685:95 ANNEX A
CLASS
0
GENERAL SPECIFICATIONS
CARACTERISTIQUESREQUIREMENT TEST METHOD
0


∆ t av, (relative to nominal value)0,30
t max -t min0,30
EN 13329 ANNEX A
0∆ l0,30EN 13329 ANNEX A; EN 13329 ANNEX A
0∆ w av, (relative to nominal value)0,10w max - w min0,20EN 13329 ANNEX A
Squareness of the element (q) Qmax =<0,10 mmEN 13329 ANNEX A
Straightness of the surface layer (s)smax =0,30 smed =0,20EN 13329 ANNEX A
Longitudinal flatness (f)0 0EN 13329 ANEXO A
Transversal flatness (f)0 0EN 13329 ANEXO A
Opening between elements (o)oaverage =<0,15 omax =<0,20EN 13329 ANNEX B
Height between elements (h)hmedio =< 0,07 hmax =<0,10EN 13329 ANNEX B
Dimensional variations after changes in relative humidity (l,w)


∆l av =<0,9 dwmedio =<0,9EN 13329 ANNEX C
Light fastness


Blue wool scale, part B02, not worse than 6 Grey scale, part A02, higher or equal to 4EN-ISO 105 / EN 20105
Static indentation


No visible changes i.e. =<0,01 mm indentation using a straight steel cylinder with 11,30 mm in diameterEN 433
Surface soundness>= 1,20 N/mm2EN 13329 ANNEX D
CLASSIFICATION REQUIREMENTS AND LEVEL OF USE
CARACTERISTIQUESREQUIREMENT TEST METHOD
Abrasion resistance


AC 5EN 13329 ANNEX E
Impact resistance


IC 2EN 13329 ANNEX F
Staining resistance


5 (gr 1 - 2) 4 (gr. 3)EN 438
Effect of a furniture leg


No damage shall be visible when tested with footEN 424
Effect of a castor chair


No changes in appearance or damage, as defined in EN425. Single-wheel castor, as defined in EN 12529:1998, 5.4.4.2. (Type W).EN 425
Thickness swelling


=< 12,0%EN 13329 ANNEX G
ADITIONAL PROPERTIES
CARACTERISTIQUESREQUIREMENT TEST METHOD
Humidity at dispatch from manufactured The element shall have a moisture content of 4% to 10%. Any single batch must be homogeneous with Hmax-Hmin = <3 %EN 322
Appearance, surface deffects Minor surface defect as defined in EN438 are permittedEN 438
Edges sealingComplete edge sealed with oil-wax product for enhance water resistantINTERNAL
Mechanical locking strenght


fmax long. >=5 KN/m fmax transv. >=5 KN/m f0,2 long. >=3 KN/m f0,2 transv. >=3 KN/mISO 24334:2006
Formaldehyde emissions HCHO
E1=< 3,5 mg/m2h (EN 717-2) E1=< 0,124 mg/m3 (EN 717-1)EN 14041 / EN 717-1 / EN 717-2
PCP ContentUndectectableEN 14041 / CEN/TR14823
Reaction to fire

Bfl s1 EN 14041 / EN 13501-1 / EN ISO 9239-1 / EN ISO 11925-2
Slip resistance coefficient under dry conditions


Class DS (>=0,3)EN 14041 / EN 13893
Slip resistance35>Rd>15EN 12633:2003
Class 1CTE DB SUA 1
Electrical behaviur
The measurement of the body voltage at 23șC/25% humidity are =<2kV. Fulfils the criterions for the classification as an Antistatic Floor CoveringEN 14041 / EN 1815
Electrical behaviour / vertical resistance
Antistatic Floor “ASF – Class 2” in accordance with the international standard IEC 61340-4- 1:1995EN 14041 / EN 1815
Thermal Resistance
Without Underlay: 0,06 m2·K/W + FINfloor PE Underlay 0,154 m 2·K/W + Finfloor Silent Underlay 0,127 m 2 ·K/W Suitable for warm-water underfloor heating systemsEN 14041 / EN 12664
Antibacterial efficiencyReduction of bacterial activity in 24 hours ≥ 99.9% according to tests carried out at the IMSLISO 22196
CE Certificate
0EN 14041
The above information is subject to modifications for the benefit of further improvements.

(SELECT)
Non dangerous product. Adequate ergonomic techniques and IPEs must be used when handling. Dust generated in cutting, sanding, drawmilling and other processes must be extracted from the working environment with the usual procedures in the wood industry as industrial vacuum systems and IPEs use must be observed according to law.