Open new windowRecommend selecting the PDF printerSee all data sheets


FINANCIERA MADERERA S.A. (FINSA)
N-550, KM 57
15890 SANTIAGO DE COMPOSTELA (A CORUÑA)
SPAIN
DECLARATION OF PERFORMANCE Nº 0013910/26/2018
FIBRAPAN PLUS
Manufactured at: Finsa Fibranor
Políg. Ind. de Rábade
27370 RÁBADE (ESPAÑA)
Manufactured at: Finsa Orember
Políg. Ind. San Cibrao das Viñas
32911 OURENSE (ESPAÑA)
Manufactured at: Finsa Padrón
Paraíso s/n
15900 PADRÓN (ESPAÑA)
Manufactured at: Luso Finsa
Estrada Nacional 234, Km 92.7
3524-952 NELAS (PORTUGAL)
PRODUCT TYPEINTENDED USEAVCP*
MDFInternal use as non structural component in dry conditions4
*Assessment and verification of constancy of performance system according to Annex V of regulation (EU) No 305/2011

TECHNICAL DATA-AVERAGE VALUES
Rev: 12/09/2016
PROPERTIESTEST METHOD UNITS THICKNESSES mm
>9/12>12/19>19/30
DENSITY (*)EN 323kg/m3760/750750/725725/700
INTERNAL BONDEN 319N/mm20,900,800,75
BENDING STRENGTH EN 310N/mm2252523
MODULUS OF ELASTICITY EN 310 N/mm2280028002500
THICKNESS SWELLING 24 H EN 317%151210
DIMENSIONAL MOVEMENT LENGTH/WIDTH EN 318%0,40,40,3
DIMENSIONAL MOVEMENT TICKNESS EN 318%665
SURFACE SOUNDNESS EN 311N/mm21,21,21,2
SURFACE ABSORPTION (TWO FACES) EN 382-1mm> 150> 150> 150
MOISTURE CONTENT EN 322%7+/-37+/-37+/-3
GRIT CONTENT ISO 3340 % Weight≤ 0,05≤ 0,05≤ 0,05
FORMALDEHYDE CONTENT EN ISO 12460-5mg/100 g≤ 8≤ 8≤ 8
REACTION TO FIRETABLA EN 13986:2004+A1:2015 IEN 13501-1ClassD-s2,d0(**)D-s2,d0(***)D-s2,d0
SOUND ABSORPTION COEFFICIENT (Α) (250 A 500 HZ)EN 13984:2004+A1:2015α 0.100.100.10
SOUND ABSORPTION COEFFICIENT (Α) (1000 A 2000 HZ)EN 13984:2004+A1:2015α 0.200.200.20
THERMAL CONDUCTIVITYEN 13984:2004+A1:2015W/ (m·K)0.140.130.13
AIRBORNE SOUND INSULATION (SURFACE MASS) (R)EN 13986:2004+A1:2015db272831
WATER VAPOUR PERMEABILITY DRY CUPEN 13986:2004+A1:2015μ 282625
WATER VAPOUR PERMEABILITY
WET CUP
EN 13986:2004+A1:2015
μ
18
17
16
BIOLOGICAL DURABILITY USEEN 13986:2004+A1:2015Class of use111
CONTENT OF PENTACHLOROPHENOL (PCP)EN 13986:2004+A1:2015%< 5< 5< 5
(*) VALUES TO BE CONSIDERED AS A ROUGH GUIDE ONLY.

(**) Mounted without an air gap behind the FIBRAPAN PLUS. Mounted with a closed air gap not more than 22 mm behind the FIBRAPAN PLUS classification D-s2,d2. Classification E for any other less restrictive condition. Commission Decision 2007/348/EC.

(***) Mounted without an air gap behind the FIBRAPAN PLUS, or with a closed air gap behind the FIBRAPAN PLUS for thicknesses equal or greater than 15mm or with an open air gap behind the FIBRAPAN PLUS for thicknesses equal or greater than 18 mm. Mounted with a closed air gap not more than 22 mm behind the FIBRAPAN PLUS classification D-s2,d2 in thicknesses between >12 mm and 18 mm. Commission Decision 2007/348/EC.

These physical-mechanical values improve/comply with those established by EN 622-5:2009 European Standard, Table 3. Requirements for boards for use in dry conditions (type MDF)

FIBRAPAN PLUS meets Class E1 requirements (analysed according to EN ISO 12460-5) as defined in EN 622-1:2003 European Standard.

FIBRAPAN PLUS is endorsed by AITIM Quality Labels.

The performance of the reference product are in compliance with the performance declared above
This Declaration of Perfomance is issued under the sole responsibility of FINANCIERA MADERERA S.A. (FINSA)
Javier Portela
FINSA R&D + Quality Director
Santiago de Compostela 10/26/2018