Open new windowRecommend selecting the PDF printerSee all data sheets


FINANCIERA MADERERA S.A. (FINSA)
N-550, KM 57
15890 SANTIAGO DE COMPOSTELA (A CORUÑA)
SPAIN
DECLARATION OF PERFORMANCE Nº 0003910/26/2018
FIMAPLAST
Manufactured at: Finsa Santiago
Carretera N-550 km 57
15707 SANTIAGO DE COMPOSTELA (ESPAÑA)
Manufactured at: Finsa Cella I
Partida de Hazas s/n
44370 CELLA (ESPAÑA)
Manufactured at: Luso Finsa
Estrada Nacional 234, Km 92.7
3524-952 NELAS (PORTUGAL)
Manufactured at: Finsa Padrón
Paraíso s/n
15900 PADRÓN (ESPAÑA)
Manufactured at: Finsa Orember
Políg. Ind. San Cibrao das Viñas
32911 OURENSE (ESPAÑA)
PRODUCT TYPEINTENDED USEAVCP*
P2Internal use as non structural component in dry conditions4
*Assessment and verification of constancy of performance system according to Annex V of regulation (EU) No 305/2011

TECHNICAL DATA-AVERAGE VALUES
Rev: 06/07/2018
PROPERTIESTEST METHOD UNITS THICKNESSES mm
6>6-13>13/20>20/25>25/32>32/40
DENSITY (*)EN 323kg/m3720/700700/650650/620620/595590/580575/560
INTERNAL BONDEN 319N/mm2≥ 0,45≥ 0,40≥ 0,35≥ 0,30≥ 0,25≥ 0,20
BENDING STRENGTH EN 310N/mm2≥ 12≥ 11≥ 11≥ 10,5≥ 9,5≥ 8.5
MODULUS OF ELASTICITY EN 310 N/mm2≥ 1950≥ 1800≥ 1600≥ 1500≥ 1350≥ 1200
MOISTURE CONTENT EN 322%8+/-38+/-38+/-38+/-38+/-38+/-3
FORMALDEHYDE EMISSION CLASS E1EN ISO 12460-3mg/(m2.h)≤ 3.5≤ 3.5≤ 3.5≤ 3.5≤ 3.5≤ 3.5
REACTION TO FIRETABLA EN 13986:2004+A1:2015 IEN 13501-1ClassED-s2,d0**D-s2,d0***D-s2,d0D-s2,d0D-s2,d0
REACTION TO FIRETABLA EN 13986:2004+A1:2015 IEN 13501-1ClassEflDfl-s1****Dfl-s1Dfl-s1Dfl-s1Dfl-s1
SOUND ABSORPTION COEFFICIENT (Α) (250 A 500 HZ)EN 13984:2004+A1:2015α 0.100.100.100.100.100.10
SOUND ABSORPTION COEFFICIENT (Α) (1000 A 2000 HZ)EN 13984:2004+A1:2015α 0.250.250.250.250.250.25
THERMAL CONDUCTIVITYEN 13984:2004+A1:2015W/ (m·K)0.140.140.130.120.120.12
AIRBORNE SOUND INSULATION (SURFACE MASS) (R)EN 13986:2004+A1:2015dbNPD2426282931
WATER VAPOUR PERMEABILITY DRY CUPEN 13986:2004+A1:2015μ 505050505050
WATER VAPOUR PERMEABILITY
WET CUP
EN 13986:2004+A1:2015
μ
17
16
15
15
15
15
BIOLOGICAL DURABILITY USEEN 13986:2004+A1:2015Class of use111111
CONTENT OF PENTACHLOROPHENOL (PCP)EN 13986:2004+A1:2015%< 5< 5< 5< 5< 5< 5

(*) VALUES TO BE CONSIDERED AS A ROUGH GUIDE ONLY.

(**) Minimun thickness 9mm.Mounted without an air gap behind the FIMAPLAST. Mounted with a closed air gap not more than 22 mm behind the FIMAPLAST classificationD-s2,d2. Classification E for any other more restrictive condition. Commission Decision 2007/348/EC.

(***) Mounted without an air gap behind the FIMAPLAST, or with a closed air gap behind the FIMAPLAST for thicknesses equal or greater than 15mm or with an open air gap behind the FIMAPLAST for thicknesses equal or greater than 18 mm. Mounted with a closed air gap not more than 22 mm behind the FIMAPLAST classification D-s2,d2 in thicknesses between 10 and 18 mm. Commission Decision 2007/348/EC

(****) Minimun thickness 9 mm

(v*) Applies only when balnced recovering are used in both faces

These physical-mechanical values improve/comply with the P2 classification established in EN 312:2010 European Standard, Table 3. Boards for indoor applications (including furniture) in dry environments (Type P2). Requirements for the specified mechanical properties.

This product meets Class E1 requirements as defined in EN 14322:2017 European Standard.

This product is endorsed by AITIM Quality Labels.

HANDLING/STORAGE:

It must always be stored under cover and on a flat surface.
65% of humidity is the ideal condition for its storage, dryer or more moist environments should be avoided.
It must never be in direct contact with water.
Blocks must always be lined up with the vertical.
Never pile up more than 4 heights.
If the packaging is damaged during its handling, it must be packed again so the product is correctly preserved.

If the piling-up conditions or the changes in moisture or temperature above mentioned are not respected in the warehouses or the processing areas, they may cause irreversible deformations and warpings.

The performance of the reference product are in compliance with the performance declared above
This Declaration of Perfomance is issued under the sole responsibility of FINANCIERA MADERERA S.A. (FINSA)
Javier Portela
FINSA R&D + Quality Director
Santiago de Compostela 10/26/2018
Google+
Google+