Open new windowRecommend selecting the PDF printerSee all data sheets


FINANCIERA MADERERA S.A. (FINSA)
N-550, KM 57
15890 SANTIAGO DE COMPOSTELA (A CORUÑA)
SPAIN
DECLARATION OF PERFORMANCE Nº 0013111/08/2018
SUPERPAN TECH P4
Manufactured at: Luso Finsa
Estrada Nacional 234, Km 92.7
3524-952 NELAS (PORTUGAL)
PRODUCT TYPEINTENDED USEAVCP*NOTIFIED BODY AND REFERENCECERTIFICATE NUMBER
P4Internal use as structural component in dry conditions2+AENOR 00990099/CPR/A65/0036
*Assessment and verification of constancy of performance system according to Annex V of regulation (EU) No 305/2011

PROPERTIESTEST METHOD UNITS THICKNESSES mm
8/13>13/20>20/25>25/32>32/40
CHARACTERISTIC STRENGTH
TABLE 5 EN 12369-1:2001
....
BENDING FMEN 13986:2004+A1:2015N/mm214.212.510.89.27.5
COMPRESSION FCEN 13986:2004+A1:2015N/mm212.011.19.69.07.6
TENSION FTEN 13986:2004+A1:2015N/mm28.97.96.96.15.0
PANEL SHEAR FVEN 13986:2004+A1:2015N/mm26.66.15.54.84.4
PLANAR SHEAR FREN 13986:2004+A1:2015N/mm2NPDNPDNPDNPDNPD
CHARACTERISTIC STIFFNESS (MOE)
TABLE 5 EN 12369-1:2001
TENSION ETEN 13986:2004+A1:2015N/mm218001700160014001200
COMPRESSION ECEN 13986:2004+A1:2015N/mm218001700160014001200
BENDING EMEN 13986:2004+A1:2015N/mm232002900270024002100
PANEL SHEAR FVEN 13986:2004+A1:2015N/mm2860830770680600
POINT LOAD FULS
FOR FLOORS AND ROOFS
EN 13986:2004+A1:2015N/mm2
POINT LOAD MEAN STIFFNESS
FOR FLOORS AND ROOFS
EN 13986:2004+A1:2015N/mm2
POINT LOAD SERVICEABILITY FSLS
FOR FLOORS AND ROOFS
EN 13986:2004+A1:2015N/mm2
RACKING RESISTANCE
FOR WALLS
EN 13986:2004+A1:2015N/mm2
SOFT BODY IMPACT RESISTANCE
PARA FORJADOS, CUBIERTAS Y MUROS
EN 13986:2004+A1:2015N/mm2
FINANCIERA MADERERA S.A. (FINSA)
N-550, KM 57
15890 SANTIAGO DE COMPOSTELA (A CORUÑA)
SPAIN
DECLARATION OF PERFORMANCE Nº 0013111/08/2018
SUPERPAN TECH P4
TECHNICAL DATA-AVERAGE VALUES
Rev: 11/08/2018
PROPERTIESTEST METHOD UNITS THICKNESSES mm
8/13>13/20>20/25>25/32>32/40
DENSITY (*)EN 323kg/m3720/690660650640640
INTERNAL BONDEN 319N/mm20,400,350,300,250,20
BENDING STRENGTH EN 310N/mm22321201918
MODULUS OF ELASTICITY EN 310 N/mm229002800250022002000
THICKNESS SWELLING 24 H EN 317%1615151514
SURFACE SOUNDNESS EN 311N/mm2>0,81,01,01,01,0
MOISTURE CONTENT EN 322%8+/-38+/-38+/-38+/-38+/-3
FORMALDEHYDE CONTENT EN ISO 12460-5mg/100 g≤ 8,0≤ 8,0≤ 8,0≤ 8,0≤ 8,0
SCREW HOLDING. EDGEEN-320N700700700700700
SCREW HOLDING. SURFACEEN-320N900900900900900
REACTION TO FIRETABLA 8 EN 13986:2004+A1:2015 IEN 13501-1ClassD-s2, d0 (**)D-s2, d0 (***)D-s2, d0D-s2, d0D-s2, d0
REACTION TO FIRETABLA 8 EN 13986:2004+A1:2015 IEN 13501-1ClassDfl-s1 (****)Dfl-s1Dfl-s1Dfl-s1Dfl-s1
SOUND ABSORPTION COEFFICIENT (Α) (250 A 500 HZ)EN 13984:2004+A1:2015α 0.100.100.100.100.10
SOUND ABSORPTION COEFFICIENT (Α) (1000 A 2000 HZ)EN 13984:2004+A1:2015α 0.250.250.250.250.25
THERMAL CONDUCTIVITYEN 13984:2004+A1:2015W/ (m·K)0.150.140.130.130.13
AIRBORNE SOUND INSULATION (SURFACE MASS) (R)EN 13986:2004+A1:2015db2528293132
WATER VAPOUR PERMEABILITY DRY CUPEN 13986:2004+A1:2015μ 5050 505050
18
17
17
17
17
BIOLOGICAL DURABILITY USEEN 13986:2004+A1:2015Class of use11111
CONTENT OF PENTACHLOROPHENOL (PCP)EN 13986:2004+A1:2015%< 5< 5< 5< 5< 5
MECHANICAL DURABILITYEN 13986:2004+A1:2015Kmod KdefEN 1995-1:2004 3.1 & 3.2EN 1995-1:2004 3.1 & 3.2EN 1995-1:2004 3.1 & 3.2EN 1995-1:2004 3.1 & 3.2EN 1995-1:2004 3.1 & 3.2
(*) VALUES TO BE CONSIDERED AS A ROUGH GUIDE ONLY.

(**) Minimun thickness 9mm.Mounted without an air gap behind the SUPERPAN TECH P4. Mounted with a closed air gap not more than 22 mm behind the SUPERPAN TECH P4 classification D-s2,d2. Classification E for any other less restrictive condition. Commission Decision 2007/348/EC.

(***) Mounted without an air gap behind the SUPERPAN TECH P4, or with a closed air gap behind the SUPERPAN TECH P4 for thicknesses equal or greater than 15mm or with an open air gap behind the SUPERPAN TECH P4 for thicknesses equal or greater than 18 mm. Mounted with a closed air gap not more than 22 mm behind the SUPERPAN TECH P4 classification D-s2,d2 in thicknesses between 10 and 18 mm. Commission Decision 2007/348/EC

(****) Minimun thickness 9 mm

These physical-mechanical values improve/comply with the P4 classification established in EN 312:2010 European Standard, Table 6. Structural boards used in dry conditions (Type P4). Requirements for the specified mechanical and swelling properties.

SUPERPAN TECH P4 meets Class E1 requirements (analysed according EN-ISO 12460-5) as defined in EN 312:2010 European Standard.

SUPERPAN TECH P4 holds CE Certificate of conformity of the factory production control issed by the European Notified Body AENOR.

SUPERPAN TECH P4 is endorsed by AITIM Quality Labels.

The performance of the reference product are in compliance with the performance declared above
This Declaration of Perfomance is issued under the sole responsibility of FINANCIERA MADERERA S.A. (FINSA)
Javier Portela
FINSA R&D + Quality Director
Santiago de Compostela 11/08/2018
Google+
Google+