Open new windowRecommend selecting the PDF printerSee all data sheets


FINANCIERA MADERERA S.A. (FINSA)
N-550, KM 57
15890 SANTIAGO DE COMPOSTELA (A CORUÑA)
SPAIN
DECLARATION OF PERFORMANCE Nº 0013810/26/2018
FIBRANOR TS / FIBRAPAN TS
Manufactured at: Finsa Fibranor
Políg. Ind. de Rábade
27370 RÁBADE (ESPAÑA)
PRODUCT TYPEINTENDED USEAVCP*
MDFInternal use as non structural component in dry conditions4
*Assessment and verification of constancy of performance system according to Annex V of regulation (EU) No 305/2011

TECHNICAL DATA-AVERAGE VALUES
Rev: 05/30/2018
PROPERTIESTEST METHOD UNITS THICKNESSES mm
2,5/4>4/6>6/10
DENSITY (*)EN 323kg/m3860-830830-820820-780
INTERNAL BONDEN 319N/mm21,31,21,1
BENDING STRENGTH EN 310N/mm2404040
MODULUS OF ELASTICITY EN 310 N/mm2270027002700
THICKNESS SWELLING 24 H EN 317%322417
DIMENSIONAL MOVEMENT LENGTH/WIDTH EN 318%0,40,40,4
DIMENSIONAL MOVEMENT TICKNESS EN 318%10106
SURFACE SOUNDNESS EN 311N/mm21,21,21,2
SURFACE ABSORPTION (TWO FACES) EN 382-1mm>150>150>150
MOISTURE CONTENT EN 322%7+/-37+/-37+/-3
GRIT CONTENT ISO 3340 % Weight≤ 0,05≤ 0,05≤ 0,05
FORMALDEHYDE CONTENT EN ISO 12460-5mg/100 g≤ 8≤ 8≤ 8
REACTION TO FIRETABLA EN 13986:2004+A1:2015 IEN 13501-1ClassE (**)E (**)E (***)
SOUND ABSORPTION COEFFICIENT (Α) (250 A 500 HZ)EN 13984:2004+A1:2015α 0.100.100.10
SOUND ABSORPTION COEFFICIENT (Α) (1000 A 2000 HZ)EN 13984:2004+A1:2015α 0.200.200.20
THERMAL CONDUCTIVITYEN 13984:2004+A1:2015W/ (m·K)0.160.150.14
AIRBORNE SOUND INSULATION (SURFACE MASS) (R)EN 13986:2004+A1:2015dbNPDNPDNPD
WATER VAPOUR PERMEABILITY DRY CUPEN 13986:2004+A1:2015μ 333130
WATER VAPOUR PERMEABILITY
WET CUP
EN 13986:2004+A1:2015
μ
22
21
20
BIOLOGICAL DURABILITY USEEN 13986:2004+A1:2015Class of use111
CONTENT OF PENTACHLOROPHENOL (PCP)EN 13986:2004+A1:2015%< 5< 5< 5
(*) VALUES TO BE CONSIDERED AS A ROUGH GUIDE ONLY.

(**) Commission Decision 2007/348/EC.

(***) Mounted without an air gap behind the FIBRANOR TS / FIBRAPAN TS of thickness ≥9 mm. Mounted with a closed air gap not more than 22 mm behind the FIBRANOR TS / FIBRAPAN TS of thickness ≥9 mm classification D-s2,d2. Classification E for any other more restrictive condition. Commission Decision 2007/348/EC.

These physical-mechanical values improve/comply with those established in EN 622-5:2009 European Standard, Table 3. General requirements for boards to be used in dry conditions (Type MDF).

FIBRANORTS/FIBRAPAN TS meet Class E1 requirements (analysed according EN ISO 12460-5) as defined in EN 622-:2003 European Standard.

The performance of the reference product are in compliance with the performance declared above
This Declaration of Perfomance is issued under the sole responsibility of FINANCIERA MADERERA S.A. (FINSA)
Javier Portela
FINSA R&D + Quality Director
Santiago de Compostela 10/26/2018
Google+
Google+