Open new windowRecommend selecting the PDF printerSee all data sheets


FINANCIERA MADERERA S.A. (FINSA)
N-550, KM 57
15890 SANTIAGO DE COMPOSTELA (A CORUÑA)
SPAIN
DECLARATION OF PERFORMANCE Nº 0012310/26/2018
SUPERPAN H DECOR
Manufactured at: Luso Finsa
Estrada Nacional 234, Km 92.7
3524-952 NELAS (PORTUGAL)
Manufactured at: Finsa Santiago
Carretera N-550 km 57
15707 SANTIAGO DE COMPOSTELA (ESPAÑA)
Manufactured at: Finsa Cella I
Partida de Hazas s/n
44370 CELLA (ESPAÑA)
Manufactured at: Finsa Padrón
Paraíso s/n
15900 PADRÓN (ESPAÑA)
PRODUCT TYPEINTENDED USEAVCP*
P2Internal use as non structural component in dry conditions4
*Assessment and verification of constancy of performance system according to Annex V of regulation (EU) No 305/2011

TECHNICAL DATA-AVERAGE VALUES
Rev: 01/04/2016
PROPERTIESTEST METHOD UNITS THICKNESSES mm
8/13>13/20>20/25>25/32>32/40
DENSITY (*)EN 323kg/m3710/660640620620610
INTERNAL BONDEN 319N/mm20,450,450,400,350,30
BENDING STRENGTH EN 310N/mm21616151413
MODULUS OF ELASTICITY EN 310 N/mm224002300200017001500
THICKNESS SWELLING 24 H EN 317%1714131312
MOISTURE CONTENT EN 322%8+/-38+/-38+/-38+/-38+/-3
FORMALDEHYDE EMISSION CLASS E1EN ISO 12460-3mg/(m2.h)≤ 3.5≤ 3.5≤ 3.5≤ 3.5≤ 3.5
REACTION TO FIRETABLA EN 13986:2004+A1:2015 IEN 13501-1ClassD-s2,d0 (**)D-s2,d0 (***)D-s2,d0D-s2,d0D-s2,d0
REACTION TO FIRETABLA EN 13986:2004+A1:2015 IEN 13501-1ClassDfl-s1 (****)Dfl-s1Dfl-s1Dfl-s1Dfl-s1
SWELLING IN THICKNESS AFTER CYCLIC TEST (V313)EN 321 / EN 317%1413121211
INTERNAL BOND AFTER CYCLIC TEST (V313)EN 321 / EN 319N/mm20,150,130,120,100,09
SOUND ABSORPTION COEFFICIENT (Α) (250 A 500 HZ)EN 13984:2004+A1:2015α 0.100.100.100.100.10
SOUND ABSORPTION COEFFICIENT (Α) (1000 A 2000 HZ)EN 13984:2004+A1:2015α 0.250.250.250.250.25
THERMAL CONDUCTIVITYEN 13984:2004+A1:2015W/ (m·K)0.140.140.130.120.12
AIRBORNE SOUND INSULATION (SURFACE MASS) (R)EN 13986:2004+A1:2015db2427293031
BIOLOGICAL DURABILITY USEEN 13986:2004+A1:2015Class of use1 & 21 & 21 & 21 & 21 & 2
CONTENT OF PENTACHLOROPHENOL (PCP)EN 13986:2004+A1:2015%<5<5<5<5<5
(*) VALUES TO BE CONSIDERED AS A ROUGH GUIDE ONLY.

(**) Minimun thickness 9mm.Mounted without an air gap behind the SUPERPAN H DECOR. Mounted with a closed air gap not more than 22 mm behind the SUPERPAN H DECOR classificationD-s2,d2. Classification E for any other more restrictive condition. Commission Decision 2007/348/EC.

(***) Mounted without an air gap behind the SUPERPAN H DECOR, or with a closed air gap behind the SUPERPAN H DECOR for thicknesses equal or greater than 15mm or with an open air gap behind the SUPERPAN H DECOR for thicknesses equal or greater than 18 mm. Mounted with a closed air gap not more than 22 mm behind the SUPERPAN H DECOR classification D-s2,d2 in thicknesses between 10 and 18 mm. Commission Decision 2007/348/EC

(****)Minimun thickness 9 mm

(v*) Thickness ≥15 mm and balanced recoverings.

These physical-mechanical values improve/comply with the P3 classification established in EN 312:2010 European Standard, Tables 4 and 5. Non-structural boards used in humid conditions (Type P3). Requirements for the specified mechanical and swelling properties. Requirements for moisture resistance (Option 1).

SUPERPAN H DECOR meets Class E1 requirements defined in the European Standard EN 14322.

SUPERPAN H DECOR is endorsed by AITIM Quality Label.

HANDLING/STORAGE:

It must always be stored under cover and on a flat surface.
65% of humidity is the ideal condition for its storage, dryer or more moist environments should be avoided.
It must never be in direct contact with water.
Blocks must always be lined up with the vertical.
Never pile up more than 4 heights.
If the packaging is damaged during its handling, it must be packed again so the product is correctly preserved.

If the piling-up conditions or the changes in moisture or temperature above mentioned are not respected in the warehouses or the processing areas, they may cause irreversible deformations and warpings.

The performance of the reference product are in compliance with the performance declared above
This Declaration of Perfomance is issued under the sole responsibility of FINANCIERA MADERERA S.A. (FINSA)
Javier Portela
FINSA R&D + Quality Director
Santiago de Compostela 10/26/2018
Google+
Google+